2. Square flange seat: F200 series (F203-F220), F300 series (F305-F328)

This type of product is equipped with 2 series bearings, 3 series bearings, Generally installed on the side wall of the machine, the structure is simple, the installation is convenient, and it is suitable for heavy load occasions. It is the most widely used type of flanged housing.

3. Diamond flange seat: FL200 series (F203-F218), FL300 series (FL305-FL315)

This type of product is equipped with 2 series bearings, 3 series bearings, The structure is light and easy to install, and it is suitable to be installed in the transmission part with a small area. The center distance of the two bolt holes is the same as the center distance of the diagonal bolt holes of the same type of square seat. Therefore, it can replace the square seat.

4. Narrow vertical seat: PA200 series (PA203-PA213), PA300 series (PA305-PA313)

This type of product is equipped with 2 series bearings, 3 series bearings, bottom There are two mounting screw holes, and the width is greatly compressed, which is suitable for parts with limited installation area.

5. High center vertical seat: PH200 series (PH203-PH213)

This type of product is equipped with 2 series bearings, the usage and use are the same as UCP200, the difference is that the shaft center is high Taller than normal uprights.

6. Suspension seat: HA200 series (HA203-HA213)

This type of product is equipped with 2 series bearings, and one end of the bearing seat is provided with an adjusting screw hole, which can The bearing seat is connected to the screw to adjust the installation position, and is generally used in situations where the load is small.

7. Adjustable diamond-shaped seat: FA200 series (FA203-FA213)

This type of product is equipped with 2 series bearings, which is a deformation of the diamond-shaped seat. Change one of the bolts to an arc slot centered in the other hole. Therefore, the position of the shaft center can be adjusted within a certain range.

8. Three-hole flange diamond-shaped seat: FB200 series (FB203-FB213)

This type of product is equipped with 2 series bearings, which is a deformation of the diamond-shaped seat. The bolt holes are concentrated on one side of the seat. It is suitable for parts where the installation surface is in a vertical state, and can be used instead of a vertical seat.

9. Boss circular flange seat: FC200 series (FC203-FC220)

This type of product is equipped with 2 series bearing, which is a circular flange bearing seat and has a bottom surface. With a round boss, it can be placed in the round hole of the rack, so the installation precision is high and the positioning is accurate.

10. Boss square bearing seat: FS300 series (FS305-FS328)

This type of product is equipped with 3 series bearing, which is a square flange bearing seat and has a circle on the bottom. It can be placed in the round hole of the rack, so the installation precision is high and the positioning is accurate.

11. Slider seat: T200 series (T203-T220), T300 series (T305-T328), K200 series (K203-K212)

This type of product is equipped with 2 Series bearings, 3 series bearings, there are two chutes up and down. Can move back and forth on the rack. Therefore, it is most suitable for occasions where the distance between axes needs to be adjusted. The axis of the machine can also move during operation. Mostly used on belts, chains and other transmission shafts.

12. Ring seat: C200 series (C203-C218), C300 series (C305-C328), etc.

This type of product is equipped with 2 series bearings, 3 series bearings, bearings The outer diameter of the seat can be embedded in the pre-cut hole of the frame, which can bear a large radial load and be used on a heavier frame.

Model of outer spherical steel stamping seat:

1. Stamping vertical seat: PP200 series

Equipped with 2 series bearings, the upper and lower shells are stamped from steel plates Compared with the cast iron vertical seat, it has the advantages of light weight and small volume, and is the seat type with the smallest installation space in the vertical seat. But it can only be applied to occasions where the load is small.

2. Stamping circular seat CY200 series

Equipped with 2 series bearings, it is composed of a stamped circular shell with two interchangeable halves, washed with high-quality steel plates, and its function is similar to that of the same kind Similar to the cast iron seat, because the stamping seat has a light design and compact structure, it is suitable for a small installation space, and it is very ideal for the application of lifting and closing occasions with small load and low speed.

3. Stamping diamond seat CL200 series

Equipped with 2 series bearings, this stamping seat has a good installation space. It is the smallest in appearance and the most weight in spherical bearings with seats. Light seat type.