loading

Best Wholesale Bearing Suppliers With Custom Service, JNSN Bearing Supplier Yours Ideal Partner

Can full complement cylindrical roller bearings withstand axial loads?

by:JNSN     2022-11-27
Full complement cylindrical roller bearings are designed to withstand heavy loads. Under the same width, this kind of bearing can accommodate more rollers than the bearing with cage, and has a very high bearing capacity; but its allowable speed is much lower than that of the full complement cylindrical roller bearing with a cage. Full complement double row cylindrical roller bearings are available in 4 layouts, 3 open layouts and 1 sealed layout. All products are of short and long separation type, and the outer ring has lubricating grooves and lubricating holes for easy lubrication. 1. NNCL type: NNCL type bearing has 3 ribs on the inner ring and no ribs on the outer ring. There is a fixed ring in the middle of the outer ring between the two sets of rollers, which can prevent the rollers from running out and keep the bearing as one. NNCL type bearings can tolerate certain axial displacement due to thermal expansion or between the shaft and the bearing housing. This displacement occurs inside the bearing, not the inner ring and the shaft or the outer ring and the housing. Therefore, during the rolling process of the bearing, the conflict does not increase. Bearings of this type are suitable for use as floating end bearings. The outer ring of the bearing has no rib, so the product of this layout can only bear radial load, not axial load. 2. NNCF type: NNCF type bearing has 3 ribs on the inner ring and one rib on the outer ring. Axial positioning in one direction is possible. The outer ring is fitted with a snap ring at the other end, keeping the bearing in one piece. The snap ring is to prevent the bearing from being scattered during the handling process, and cannot be subjected to axial load. This type of bearing can withstand high radial loads and unidirectional axial loads, so that axial positioning of the shaft in one direction can be achieved. In the other direction, it is used as a floating bearing. 3. NNC type: The inner ring of the NNC type bearing is similar to the inner ring of NNCL and NNCF, and has 3 ribs. The outer ring of the bearing is split and fixed by a few parts, so it cannot bear the axial load in the direction of the medicine. The 2 split outer rings each have a rib for axial positioning in both directions. Bearings can withstand high radial forces and bidirectional axial forces. 4. NNF type: also called Solon bearing (double row cylindrical roller bearing with retaining groove in outer ring). NNF type has NNF50 and 3194 size series, the bearing has seals on both sides and has been filled with grease. The inner ring is split with 3 ribs, fixed by a snap ring, and the outer ring has a middle rib, which can be used for axial positioning in two directions. Because of the very large distance between the two rows of rollers, the bearing can experience overturning moments. The outer ring of the NNF type bearing is 1 mm narrower than the inner ring, and there are 2 retaining grooves on the outer circle of the outer ring. It is thus possible to dispense with the spacer ring between the inner ring and the adjacent components, as used on the Soren. These bearings are very rigid and can withstand very high radial forces and moderate bidirectional axial forces. Full complement cylindrical roller bearings are equipped with contact seals made of polyurethane (AU) on both sides, which can provide a good sealing effect. The bearing is filled with lithium-based grease and can be used between -40 and +80°C. This kind of sealed bearing, under the necessary premise, does not need protection. However, in the case of wet or serious contamination, or when running at medium to high speed, the bearing must be lubricated on time, and the lubrication hole on the inner ring or the outer ring can be used for lubrication. The sealing ring can also be removed from the bearing, and the bearing can be used as an open bearing. In general, proper use of full complement cylindrical roller bearings can achieve fatigue life. But in case of unexpected early damage, it can no longer be used. Unlike fatigue life, this early damage is called a failure or accident. Most of them are due to insufficient consideration of installation and use and lubrication, resulting in the entry of foreign objects. The damage of the full complement cylindrical roller bearing is like scratches on the inner and outer ring ribs of the bearing. The cause may be insufficient lubricant. Defective oil supply structure, foreign matter intrusion, bearing installation error or too large shaft deflection can be caused by various reasons mentioned above. Therefore, only bearing damage is studied, and it is difficult to know the real cause of damage. However, if you fully understand the machine, the working conditions and the surrounding structure of its bearings, the conditions before and after the failure occurs, the damage to the bearing and various causes can be analyzed, and the same failure can be prevented from happening again. Representative causes and countermeasures.
At the same time, as the recent research of JNSN shows, the benefits of improved productivity and firm performance can make implementing basic management practices worth it.
Interested in the that create such effect? Come to JNSN Bearing to see some items.
HangZhou Jnsn Bearing Imp& Exp Co., Ltd knows how important it is to offer optional extras, such as CONTACT USHrb Bearing China to provide quality products for customers.
Custom message
Chat Online
Chat Online
Leave Your Message inputting...
Sign in with: