Instructions for the use of rolling bearings

1. When installing the bearing, the force should be uniform, and it should not be hammered directly. If the interference is large, the bearing should be heated in an air heating furnace or oil furnace with automatic temperature control, and the heating temperature should be strictly controlled below 120°C.

2. Bearings equipped with nylon e cages can work continuously and stably for a long time at -40°C~120°C, and should not work more than 4 at 150°C hours, with short-term temperature peaks up to 180°C.

3. The warehouse where the bearings are stored should be clean, dry and not allowed to be stored in the same warehouse with chemical products, the relative humidity should not exceed 65%, and the bearings are not allowed to be stored on the ground.

Installation and use of deep groove ball bearings

1. When installing the bearing, the force should be uniform, and it should not be hammered directly. If the interference is large, the bearing should be heated in an air heating furnace or oil furnace with automatic temperature control, and the heating temperature should be strictly controlled below 120°C.

2. Bearings equipped with nylon cages can work continuously and stably for a long time at -40°C~120°C, and should not work more than 4 hours at 150°C , transient temperature peaks should not exceed 180°C.

3. The warehouse where the bearings are stored should be clean, dry and not allowed to be stored in the same warehouse with chemical products, the relative humidity should not exceed 65%, and the bearings are not allowed to be stored on the ground.

4. Bearings in stock should be re-cleaned every other year and packed for rust prevention.

Installation and use of angular contact ball bearings

1. When installing the bearing, the force should be uniform, and it should not be hammered directly. If the interference is large, the bearing should be heated in an air heating furnace or oil furnace with automatic temperature control, and the heating temperature should be strictly controlled below 100°C.

2. Bearings equipped with nylon cages can work continuously and stably for a long time at -40°C~120°C, and should not work more than 4 hours at 150°C , for a short period of time at 180°C.

3. The warehouse where the bearings are stored should be clean, dry and not allowed to be stored in the same warehouse with chemical products, the relative humidity should not exceed 65%, and the bearings are not allowed to be stored on the ground.

Installation and use of spherical roller bearings

1. The user should select the appropriate fit and diameter of the bearing according to the requirements of use to clearance. Please check the bearing code after unpacking.

2. Before the bearing is installed, if it is necessary to add grease to the bearing, the grease must be clean and appropriate.

3. When installing, it is advisable not to directly hammer the end faces of the inner and outer rings and the rollers, and to crack the inner ring or medium and small ribs. Usually the user should put the bearing in mineral oil and heat it to 90°C~100°C and install the spindle immediately. Do not use the local spray burning method for the bearing, and the user should also install it with a special sleeve when it is difficult to 'hot fit'.

4. The bearing should be well sealed and dustproof and lubricated during use, and the oil should not be cut off.

5. The bearing warehouse should be clean and dry, free of environmental pollution, the bearings should not fall to the ground, and the packaging should not be damaged. Bearings that have been in stock for more than 1 year must be re-cleaned and oiled.

Installation and use of thrust spherical roller bearings

1. When installing the bearing, the bearing p seal should be cleaned, and then Apply clean, high-quality lubricant.

2. When installing the bearing, the force should be uniform and not hammered. If the interference is large, the bearing should be heated to 90°C~100°C in mineral oil, and then installed immediately.

3. The warehouse where the bearings are stored should be clean, clean, and the relative humidity should not exceed 65%.

4. The bearings in stock should be re-cleaned and oiled every other year, and the oil-sealed packaging should be kept in good condition.

5. When using bearings, there should be good sealing and dustproof devices, and the working conditions should be checked frequently.

Cylindrical roller bearing installation and use

1. The bearing is a separate type, and the user can adjust it according to their needs when installing clearance.

2. Before use, the bearing should be cleaned with gasoline or kerosene and kept well lubricated.

3. When the bearing is installed, the bearing should be pressed into the chips, and it is strictly forbidden to knock.

4. The bearing storage place should be clean and ventilated to avoid moisture. Bearings that need to be stored for a long time should be regularly rusted.

Installation and use of thrust ball bearings

1. When installing the bearing, the bearing seal should be removed, cleaned and then coated with core damage Scratching fat addicted to Lilium oil.

2. When installing the bearing, the force should be uniform and not hammered. If the interference is large, the bearing should be heated to 90°C~100°C in mineral oil, and then installed immediately.

3. The warehouse where the bearings are stored should be clean, clean, and the relative humidity should not exceed 65%.

4. The bearings in stock should be re-cleaned and oiled every other year, and the oil-sealed packaging should be kept in good condition.

5. When using bearings, there should be good sealing and dustproof devices, and the working conditions should be checked frequently.