loading

Best Wholesale Bearing Suppliers With Custom Service, JNSN Bearing Supplier Yours Ideal Partner

PRODUCT

Brief talk: bearing installation

by:JNSN     2022-03-12

I. Installation of bearings: The installation of bearings must be carried out under dry and clean environmental conditions. Before installation, the machining quality of the mating surfaces of the shaft and the housing, the end faces of the shoulders, the grooves and the connecting surfaces should be carefully checked. All mating surfaces must be carefully cleaned and deburred, and unmachined surfaces of castings must be free of sand. Before the bearing is installed, it should be cleaned with gasoline or kerosene, used after drying, and ensure good lubrication. The bearing is generally lubricated with grease, but also can be lubricated with oil. When using grease lubrication, the grease with excellent performance such as no impurities, anti-oxidation, anti-rust and extreme pressure should be used. The filling amount of grease should be 30%-60% of the bearing and bearing housing volume, and should not be too much. The double row tapered roller bearing with sealed structure and the water pump shaft bearing have been filled with grease, which can be directly used by the user and cannot be cleaned again. When the bearing is installed, an equal pressure must be applied on the circumference of the end face of the ferrule, and the ferrule must be pressed in. Do not directly hit the end face of the bearing with tools such as a hammer to avoid damage to the bearing. In the case of a small amount of interference, the end face of the bearing ring can be pressed with a sleeve at room temperature, and the sleeve can be hit with a hammer head to press the ring evenly through the sleeve. If installed in large quantities, hydraulic presses can be used. When pressing in, it should be ensured that the end face of the outer ring and the end face of the shoulder of the shell, and the end face of the inner ring and the end face of the shaft shoulder are pressed tightly, and no gap is allowed. When the amount of interference is large, it can be installed by oil bath heating or inductor heating bearing method. The heating temperature range is 80℃-100℃, and the maximum cannot exceed 120℃. At the same time, tighten the bearing with nuts or other appropriate methods to prevent the bearing from shrinking in the width direction after cooling and causing a gap between the ring and the shaft shoulder. The clearance adjustment should be carried out at the end of the installation of the single row tapered roller bearing. The clearance value should be determined according to different operating conditions and the size of the interference. When necessary, tests should be carried out to determine. The double-row tapered roller bearing and the water pump shaft bearing have been adjusted for clearance at the factory, and do not need to be adjusted during installation. After the bearing is installed, a rotation test should be carried out. First, it should be used for the rotating shaft or bearing box. If there is no abnormality, it will be operated with power without load and at low speed, and then gradually increase the rotation speed and load according to the operation conditions, and detect noise, vibration and temperature rise. , found abnormal, should stop the operation and check. It can be delivered for use after the running test is normal. 2. Disassembly of the bearing: When the bearing is to be used continuously after being removed, an appropriate disassembly tool should be selected. When removing a ferrule with an interference fit, only the pulling force can be applied to the ferrule, and it is never allowed to transmit the removal force through the rolling element, otherwise the rolling element and the raceway will be crushed. 3. The use environment of the bearing: According to the use part, use conditions and environmental conditions, select the size and precision, and cooperate with the appropriate bearing to ensure the life and reliability of the bearing. 1. Use parts: Tapered roller bearings are suitable for bearing combined radial and axial loads mainly based on radial loads. They are usually used in pairs with two sets of bearings. They are mainly used in the front and rear hubs of automobiles, driving bevel gears, differential Gearboxes, reducers and other transmission parts. 2. The allowable speed: in the environment of correct installation and good lubrication, the allowable speed is 0.3-0.5 times the limit speed of the bearing. Under normal circumstances, 0.2 times the limit speed is the most appropriate. 3. Permissible inclination angle: tapered roller bearings generally do not allow the shaft to be inclined relative to the housing hole. If there is an inclination, the maximum shall not exceed 2′. 4. Allowable temperature: Under normal load, and the lubricant has high temperature resistance and sufficient lubrication, the general bearing is allowed to work at an ambient temperature of -30℃-150℃.

Custom message
Chat Online
Chat Online
Leave Your Message inputting...
Sign in with: